-
For the distribution of power from the flight battery to your six ESC's, this 24k gold plated hub offers a very neat and efficient solution. It has 3.5mm bullet connectors and 6x 3mm terminals on the back. It is stable at high currents and has minimal power loss. Features: • High efficiency • Neat instillation • 3.5mm Bullet connectors • Easy solder 3mm holes • All necessary hardware included Specs: Dimensions: 28x19x8.5mm Weight: 7g -
Specifications: Diameter: 600mm (adjustable) Weight: 450g Height: 248mm Assembled Landing Gear Width: 305mm Requires: 10-15 inch props 3 x Motors (recommended 2212, 2216, 3108, 3110, 3508, 4108) 3 x 20~40 amp ESC's Tri-copter capable flight controller 4 channel transmitter & receiver 3-4S LiPo battery -
Features: • Powerful 5.5V/6A Switching BEC • Optional programming card for convenient setup • Super fine throttle resolution provides first-rate and highly accurate linearity • Super smooth adjustable start-up mode • Constant RPM mode (governor mode) • Adjustable F3A brake. • 3 steps adjustable normal EMF brake • High anti-interference capability • Low voltage cut-off protection with automatic adjustment for NiCd/NiMH/Li-Ion/LiPo/LiFePO4 • Soft cut-off option at low voltage, slows motor RPM gradual rather than hard cutoff (LVC) • Low voltage cut-off can be disabled • Variable cut-off voltage / cell • Active free-wheeling circuit allows for unlimited "partial load" capability • LED status display • Adjustable motor timing from 0° to 30° • Blocked rotation protection (senses a jammed motor and stops motor rotation) • Motor reversing from ESC (no need to change ESC/motor wires) • Over-temperature protection and overload alarm • Anti sparking circuit: reduces connection sparks (for HV ESC) • Throttle signal lose protection. If the signal is lost for 3 seconds, the power will automatically cut-off. • Safe power-on. (Motor will not start until throttle is returned to lowest position) Max Cont Current: 80A Max Burst Current: 100A for 10 seconds Input Voltage: 2-6 cells li-XX or 6-16 Ni-MH/Ni-Cd battery BEC: 5.5V/6A Switching BEC PWM: 8~16 KHz Max RPM: 240,000rpm for 2 Poles Brushless Motor PCB Size: 50x30mm Weight: 70g (including wires) ***This ESC is compatible with both helicopter and airplane models.*** -
This FPV A/V cable connects to your ActionCam via the USB port and allows for live video output for FPV use. One end has the micro USB connector, the other has four bare wire leads for connecting to your FPV transmitter. ActionCam cameras are compatible with this cable and support the live A/V out function, as well as some SJ4000 cameras with firmware N201405270ZV01 or later*.
-
-
Specs: Constant Current: 20A Burst Current: 25A Battery: 2-4S Lipoly / 5-12s NiXX BEC: 5v / 3A Motor Type: Sensorless Brushless Size: 54 x 26 11mm Weight: 30g -
Specs: KV(RPM/V): 980 Lipo cells: 2~3s Max Watts(W): 165 Max. current: 15A (10 secs) No Load Current: 0.5A Intemal Resistance: 0.145 ohm Number of Poles: 14 Shaft Size: 3 x 2mm Dimensions(Dia.xL): 28 x 29mm Bolt Holes Spacing: 16 & 19mm Bolt thread: M3 Connector: 3.5mm bullet type connector Weight: 59g (motor only without adapters and screws) -
Specification: Wingspan : 860mm Fuselage length : 650mm Material : EPO Weight: 700g Includes: • Phazer KX Airframe • Hardware set • Optional landing gear • Decal Set Requires: 4 Channel transmitter 64mm ducted fan unit ESC 40 Amp 3 X 9g Servo Lipo battery 11.1V-25C-2200mAh -
The remote receiver can be used as a replacement for any DSMX receiver that utilizes a remote receiver. It can also be used as an optional second remote receiver for the AR9010 or fourth remote receiver for the AR9110. -
Specs. Wingspan: 1550mm Length: 948mm Flying Weight: 890g 6X 9g Servos 2X Brushless Motors 2X 30A Brushless ESC 2X Propellers Required: 4~6 Channel Transmitter and Receiver 3S 11.1V 2200mAh Lipo Battery -
Wingspan: 1550mm Length: 948mm Flying Weight: 890g Required: 4~6 Channel Transmitter and Receiver 3S 11.1V 2200mAh Lipo Battery 4~6 9g Servos 2620 1400kv Brushless Motor 20~30A Brushless ESC 8x4 Propeller -
Specs: Wingspan: 42" Length: 38" Weight: 30-36oz Wing Area: 375 sq in Required Equipment Motor:900-1100 KV Motor ESC: Castle Ice Lite 50 Battery: 3S Lipo 1500-2100mah Spinner: 40mm -
Specs: Wingspan: 944mm Length: 765mm Flying Weight: 450g~540g Wing Area: 15.2cm dm2 Includes: All Hardware Instruction Book Decal Sheet Requires: Your Own 4 Channel TX/RX 22mm~28mm Outrunner Brushless Motor 20A ESC 2 x 5/6g ~ 2 x 9g servo 1000mAh~1600mAh 3s Lipo Battery 30mm Spinner -
Wing Span: 1355mm Length: 1108mm Wing Area: 29.65Sqdm Flying Weight: 1900g Requires: 4 channel radio system 4 x metal gear micro servos 60 amp Esc 30-35 size Brushless Outrunner 2500-3000mah 3s-4s Lipo Battery -
Capacity: 2200mAh Voltage: 3S1P / 3 Cell / 11.1V Discharge: 60C Constant / 120C Burst Weight: 208.1g (including wire, plug & case) Dimensions: 104x33.6x26.17mm Balance Plug: JST-XH
